MOT checks for lights and signals on motorcycles are divided into seven sections. Please click on a link below to skip to the section of interest.
front and rear position lamps :: headlamps :: stop lamps :: rear reflectors :: indicators :: headlamp aim :: audible warnings
note: the front position light, or sidelight, is considered separate from the motorcycle’s headlight and at least 50% of all light sources within a lamp must function. If lamps are obscured by other parts of the bike they will fail.
If a motorbike has no lights at all, or they are taped, painted or permanently disconnected so as to emit no light whatsoever you can still get an MOT pass but you will receive an advisory note stating that the bike should only be used during the hours of daylight and not during times of seriously reduced visibility.
The motorcycle MOT does not cover rear fog lights or amber lights within the indicator lens of your bike.
Only one or both headlamps need to illuminate for either dipped or main beam and they must be mounted one on top of the other or symmetrically and no more than 200mm apart.
For the purposes of the MOT mopeds are only required to have a functioning dipped beam.
If your bike was built before 1 January 1931 it doesn’t need a headlight at all but if there is one it must function correctly.
Bikes which cannot exceed 25mph do not have to have a stop lamp fitted nor do mopeds which were first registered before 1 April 1986 but if fitted they must function correctly.
Only one reflector is required for the MOT but your bike will not fail for having more. Unfortunately reflective tape is not considered satisfactory.
Any motorcycle first registered before 1st August 1986 does not need indicators to pass an MOT
Bikes which cannot exceed 30mph or off-road bikes designed to carry just the rider do not need indicators but if fitted they must function correctly.
note: a specialist piece of equipment is needed to correctly check the aim of your motorbikes headlight but if you follow the guidelines below we would be happy to make minor adjustments if necessary free of charge.
front and rear position lamps :: headlamps :: stop lamps :: rear reflectors :: indicators :: headlamp aim :: audible warnings
Hi, I have a 1987 Kawasaki GPX750 project. When I bought it it had a different front end with a drum brake and no brake light switch. If I change this wheel for one with no brake at all will this be legal? Many thanks
You could replace it with a disk brake, but each wheel needs a brake.
hi my scooter 125cc sinnis harrier bought from new one day i went to set off and noticed my indicator lights was not flashing just seemed to stay on i dont no what may have caused it but any help would be appreciated thanks
Check all 4 bulbs are working, if so then a part is potentially malfunctioning and so you would need to take it to a garage.
Hi
If a bike is fitted with bar end indicators does it need rear ones.
Cheers
yes indicators need to be clearly visible from the rear (even when turning corners) so you need rear indicators.
I own a 2000 CB400SF which was imported from Japan. It was never sold in Europe. The forward indicators eliminate and stay on with the headlight when the ignition is turned on (like running/marked lights) and flash off when indicating left out right in time with the rears Is it legal for the forward indicators to stay on and fish off like this?
Hondas new msx125 has the same also and it’s sold in Europe.
Indicator running lights on imports are usually fine so long as they’re not too bright, however we usually suggest clipping the wire to the running light.
Hi
Is there a requirement to have a handlebar mounted emergency switch?
Thanks!
Simon
There is no current requirement to have a handlebar mounted emergency switch.
Does a motorcycle need a full beam headlight ?
If it has twin main/dipped beam headlights?
No, so long as the twin lights have a full beam you are fine 🙂
Can I have as side mounted number plate provided the stop and tail light are on the central line of the bike, what if the stop / tail light were on the side mounting above the plate ? Also what about MOT on number plate size (many bikes on the road have small plates)?
yes you can have a side mounted number plate, all number plates are a set sizing and anything different is illegal, your stop/tail lights can be side mounted above the plate.
Can I have indicators that also function as running lights, US style?
no because permanent lights at the back need to be Red and permanent front lights need to be white therefore they cannot function as indicators.
Hi
A couple more questions …… I have a side number plate on the rear, can I attach the reflector to the number plate, or does it need to be on the centreline of the frame ?
I assume the side number plate should be installed on the offside?
Thanks
Mark
The reflector has to be along the centreline of the bike, and yes the number plate should be installed on the offside 🙂
Hi
I am building a bobber motorcycle and the wiring loom that i have purchased flashes the rear turn signals 3 times as well as illuminating the rear brake light when the brakes are applied …….. would this pass an MOT ?
Thanks
That would fail, needs to be a static light only, no flashes of any kind.
Hi I’m just wondering if there is a set place that a headlight has to be mounted or it it could be mounted anywhere on the front of the bike like the lower forks for example
There is no fixed point for the headlights to be mounted, but it has to be able to pass the beam test as the angle of the lights could be an issue.
hi, jhonny here, just want to ask if my 50cc moped will pass an mot with bicycle wheels on it?
Unfortunately we cannot answer that question without seeing the bike and how the wheels are attached.
hi guys,
Speedo – can I mount it on top of left leg of forks below handle bars on Harley sportster, or does it have to be in the centre of the bike / bars?
What’s the latest on all-in-one tail light, brake light, rear indicator units – can you use them, or do the indicators need to be 180mm apart?
many thanks, Bill.
The Speedometer can be mounted anywhere so long as it is visible and doesn’t interfere with the steering.
In regards to the all-in-ones, most of them are fails as the lights interfere with another lights operation. It would be down to the examiners judgement on the day.
Hi there. I’m looking at importing a chopper from the US. As far as I can tell the rear lights are combined with the indicators. However, these are two separate units, one on each side of the bike. Both light up(red) when braking, but when you indicate the relevant side turns to a flashing orange light. Would this be a fail based on interruption, of a pass in that 50% remains lit? Thanks in advance.
As long as there is a central tail brake light then this should pass, however if it does fail you could just unplug the brake light from the indicators and this would solve the issue 🙂
Hi
I have a 1969 bsa a65 lightning.the brake light only works with the rear brake and was never fitted with one which functioned with the front brake.
do i need to adapt or alter my bsa so the brake light functions with both brakes please.
No need to adapt or alter your bike 🙂 that is perfectly legal.
Hi, I have a Gilera 125 scooter. My telltale indicator lamps on the dash function but the RH one remains lit when the indicators are off, then flashes on and off when the indicator is used. In your opinion is this a pass? Last year the MOT centre passed and advised on it (saying that it still performed its stated function). Need to use a different center this year.
If power is going to the indicator lamps on the dash, then power must be going to the indicators, so check your indicators. We would fail this as there is clearly an issue with the indicators.
just wondering my 2003 aprilia sr50 has 2 shields in the twin headkights which makes them look like a set of side lights would my bike still pass MOT with the shields out to make them look like dipped lights or would i have to leave them in and buy another headlight and take the shields outa them to use
Thanks
no you cannot take them out or else they would fail an MOT, They’re required to reflect the light in order to change the light intensity so they’re needed.
Hi,
Currently building up a streetfighter on a 1983 suzuki gsx750 and I am hopefully going to fit an aftermarket headlight that has twin bulbs, both of which are wired for dip and main as normal. The indicators are seperate bulbs but are with with integrated into the main body of the headlight unit and cowl. It is an “Alien” model aftermarket unit. Would this be ok or are the indicators to close to each other? please see attached link http://www.ebay.co.uk/itm/NEW-BLUE-UNIVERSAL-HEADLIGHT-STREET-FIGHTER-ALIEN-GSX-ZXR-YZF-CBR-R1-YAMAHA-CBF-/230343253582?hash=item35a1871e4e:m:mm-m4h9X2iPQ1SaBQNFc6lQ
In regards to the aftermarket headlight, we would have to fail the bike MOT as a result of 1 light interfering with another because the separation distance between the indicators is too small.
Hi, my question relates to flashing brake lights based on how hard you brake, are these UK legal now as I have seen them on alot of high end cars being released in the UK ?
Unfortunately not, the brake light has to be a constant beam.
Hi, sorry a bit of a follow up on my previous question.
I’ve just done an MOT and passed it fine but the tester asked me remove the rear indicators because I haven’t got the front indicators installed. My bike is first registered in 19/06/1986. Was the tester right in requesting to remove the rear indicators? Otherwise it would have been fail as he said.
Yep. Either four or none.